Shop headings: New Spares | Used Spares | Accessories | Brands
Thick protective tank cover for your workshop. Ideal for preventing expensive damage to your motorcycle tank when working on your bike (avoid brake fluid spills etc...) and also useful for leaving on your bike when not in use to avoid accidental scratches. Special anti-slip material on underside secures cover to your motorcycle tank when in use. Upper side is nylon for ease of cleaning.
1 in stock
£18.00
INC VAT
£15.00 EX VAT
Large dust cover for your bike when parked up in your garage. Prevents dust and dirt settling on your pride and joy. Also useful for hiding your bike from prying eyes when your garage door is open. Also see tank protector SIA00001 for extra protection.
Breathable, tear resistant fabric.
1 in stock
£19.00
INC VAT
£15.83 EX VAT
Special tool for tightening the awkward to reach distributor clamp bolts, avoids scuffed knuckles!
This part is due back in stock soon, call 01484 841395 to reserve yours
14927001 GU14927001 14 92 70 01
1492 7001 1492.7001 14.92.70.01
£27.80
INC VAT
£23.17 EX VAT
Box spanner for gearbox output shaft nut
This part is available by special order, request a quote
14905400 GU14905400 14 90 54 00
1490 5400 1490.5400 14.90.54.00
£21.00
INC VAT
£17.50 EX VAT
Clever stand which makes working on your bike much easier! This stand clamps safely to the bolts just underneath the rider footrests, and allows you to lift the bike securely in a similar action to a centrestand.
Useful substitute for a centre stand.
Needs 2 x 18mm 0.5 inch drive sockets to fit a V11 (not supplied)
This part is available by special order, request a quote
979717 MG979717
£140.00
INC VAT
£116.67 EX VAT
Get your bike running smoothly. The 2-column Carbtune Pro is for twins and will help you get your bike running smoothly and at its most powerful
Suitable for carb and fuel injected models
This part is due back in stock soon, call 01484 841395 to reserve yours
£65.70
INC VAT
£54.75 EX VAT
Tool for clutch centre gear nut
Half inch socket drive. This is a cheaper aftermarket tool- see TOA14903 for original factory item
This part is due back in stock soon, call 01484 841395 to reserve yours
14912603 GU14912603 14 91 26 03
1491 2603 1491.2603 14.91.26.03
£39.00
INC VAT
£32.50 EX VAT
Tool for crankshaft timing sprocket nut, this is a superior design tool intended for repeated use. Use for clutch centre nut on V11 Sport. Will not reach timing sprocket nut on models with Ducati charging system.
Also fits swingarm spindle nut on Stelvio.
Half inch socket drive
This part is due back in stock soon, call 01484 841395 to reserve yours
18927651 GU18927651 18 92 76 51
1892 7651 1892.7651 18.92.76.51
£41.00
INC VAT
£34.17 EX VAT
Splined tool for aligning clutch plates on reassembly, without this clutch alignment tool you risk damaging the intermediate plate. The tool screws into the back of the crankshaft to compress the clutch springs and align the clutch friction plates
Suitable only for later clutch centre spline type (e.g. clutch plate CLA05430). As used by the Gutsibits spanner monkeys on their bikes
This part is due back in stock soon, call 01484 841395 to reserve yours
30906510 GU30906510 30 90 65 10
3090 6510 3090.6510 30.90.65.10
£110.00
INC VAT
£91.67 EX VAT
Piston ring compressing tool, compresses piston rings to fit into bore. Without this tool you risk snapping piston rings, the tool also speeds up the fitting of new rings
For 57mm - 125mm bores, supplied with hex key for bore adjustment. Not suitable for CARC models
This part is available by special order, request a quote
£48.00
INC VAT
£40.00 EX VAT